Multimedia Speakers

Computer speakers, or multimedia speakers, are external speakers and are usually equipped with a male 1/8 inch stereo jack plug (usually color-coded lime green per the PC 99 standard) for computer sound cards.

However, some have an RCA connector, and some people connect the output of their computer sound cards to a conventional stereo system.

There are also USB speakers which are powered from the 5 volts at a few milliamsp provided by the USB port, per the standard. Computer speakers are usually a simplified stereo system without a radio or other media sources built in.

Computer speakers range widely in quality and in price. Typically, the computer speakers packaged with computer systems are both small and simple. There are also advanced forms of computer speakers that have graphic equalization features (bass, treble, etc.) and sometimes built-in amplifiers.

It is common to connect active/powered computer speakers to a power strip. The power outlet should, as always, preferably be grounded for safety.

Electric Heating

electric heater is an electrical appliance that converts electrical energy into heat. The heating element inside every electric heater is simply an electrical resistor, and works on the principle of Joule heating: an electric current flowing through a resistor converts electrical energy into heat energy.Domestic electrical underfloor heating:These systems are called radiant heating systems, regardless of whether they include a heat exchanger (also called a radiator) or are electrically powered.

When a home radiant heat system is turned on, current flows through a conductive heating material. For high-voltage radiant heat systems, line voltage (110 V or 230 V) current flows through the heating cable. For low-voltage systems, the line voltage is converted to low voltage (8 to 30 V) in the control unit (which contains a step-down transformer) and this low voltage is then applied to the heating element.

The heated material then heats the flooring until it reaches the right temperature set by the floor thermostat. The flooring then heats the adjacent air, which circulates, heating other objects in the room (tables, chairs, people) by convection. As it rises, the heated air will heat the room and all its contents up to the ceiling. This form of heating gives the most consistent room temperature from floor to ceiling compared to any other heating system.

Fixed Resistors

Some resistors are cylindrical, with the actual resistive material in the center (composition resistors, now obsolete) or on the surface of the cylinder (film) resistors, and a conducting metal lead projecting along the axis of the cylinder at each end(axial lead). There are carbon film and metal film resistors. The photo above right shows a row of common resistors. Power resistors come in larger packages designed to dissipate heat efficiently. At high power levels, resistors tend to be wire wound types.

Resistors used in computers and other devices are typically much smaller, often in surface-mount packages without wire leads. Resistors can also be built into integrated circuits as part of the fabrication process, using the semiconductor material as a resistor. But resistors made in this way are difficult to fabricate and may take up a lot of valuable chip area, so IC designers alternatively use a transistor-transistor or resistor-transistor configuration to simulate the resistor they require.

All wire except superconducting wire has some resistance, depending on its cross-sectional area and the conductivity of the material it is made of. Resistance wire has an accurately known resistance per unit length, and is used to make wire-wound resistors.

Units of Resistor

The SI unit of electrical resistance is the ohm (Ω). A component has a resistance of 1 Ω if a voltage of 1 volt across the component results in a current of 1 ampere, or amp, which is equivalent to a flow of one coulomb of electrical charge (approximately 6.241506 × 1018 electrons) per second. The multiples kiloohm (1 kΩ = 1000 Ω) and megaohm (1 MΩ = 106 Ω) are also commonly used.

In an ideal resistor, the resistance remains constant regardless of the applied voltage or current through the device or the rate of change of the current. Whereas real resistors cannot attain this goal, they are designed to present little variation in electrical resistance when subjected to these changes, or to changing temperature and other environmental factors.

Resistor

A resistor is a two-terminal electrical or electronic component that resists an electric current by producing a voltage drop between its terminals in accordance with Ohm's law. : The electrical resistance is equal to the voltage drop across the resistor divided by the current through the resistor. Resistors are used as part of electrical networks and electronic circuits.

A resistor is used to create a known voltage-to-current ratio in an electric circuit. If the current in a circuit is known, then a resistor can be used to create a known potential difference proportional to that current. Conversely, if the potential difference between two points in a circuit is known, a resistor can be used to create a known current proportional to that difference. Current-limiting.

By placing a resistor in series with another component, such as a light-emitting diode, the current through that component is reduced to a known safe value. A series resistor can be used for speed regulation of DC motors, such as used on locomotives and trainsets. An attenuator is a network of two or more resistors (a voltage divider) used to reduce the voltage of a signal.

A line terminator is a resistor at the end of a transmission line or daisy chain bus (such as in SCSI), designed to match impedance and hence minimize reflections of the signal. All resistors dissipate heat. This is the principle behind electric heaters. (See also electric heating and resistive heating)

Aspect Ratio Incompatibility

The television industry's changing of aspect ratios is not without difficulties, and can present a considerable problem.

Displaying a widescreen aspect (rectangular) image on a conventional aspect (square or 4:3) display can be shown:

1- in "letterbox" format, with black horizontal bars at the top and bottom

2- with part of the image being cropped, usually the extreme left and right of the image being cut off (or in "pan and scan", parts selected by an operator or a viewer)

3- with the image horizontally compressed


A conventional aspect (square or 4:3) image on a widescreen aspect (rectangular with longer horizon) display can be shown:

1- in "pillar box" format,

2- with black vertical bars to the left and right with upper and lower portions of the image cut off (or in "tilt and scan", parts selected by an operator)

3- with the image horizontally distorted


A common compromise is to shoot or create material at an aspect ratio of 14:9, and to lose some image at each side for 4:3 presentation, and some image at top and bottom for 16:9 presentation. In recent years, the cinematographic process known as Super 35 (championed by James Cameron) has been used to film a number of major movies such as Titanic, Legally Blonde, Austin Powers, and Crouching Tiger, Hidden Dragon.

This process results in a camera-negative which can then be used to create both wide-screen theatrical prints, and standard "full screen" releases for television/VHS/DVD which avoid the need for either "letterboxing" or the severe loss of information caused by conventional "pan-and-scan" cropping.

Aspect Ratio

Aspect ratio refers to the ratio of the horizontal to vertical measurements of a television's picture. Mechanically scanned television as first demonstrated by John Logie Baird in 1926 used a 7:3 vertical aspect ratio, oriented for the head and shoulders of a single person in close-up.
Most of the early electronic TV systems from the mid-1930s onward shared the same aspect ratio of 4:3 which was chosen to match the Academy Ratio used in cinema films at the time.

This ratio was also square enough to be conveniently viewed on round cathode-ray tubes (CRTs), which were all that could be produced given the manufacturing technology of the time. (Today's CRT technology allows the manufacture of much wider tubes, and the flat-screen technologies which are becoming steadily more popular have no technical aspect ratio limitations at all.) The BBC's television service used a more squarish 5:4 ratio from 1936 to 3 April 1950, when it too switched to a 4:3 ratio. This did not present significant problems, as most sets at the time used round tubes which were easily adjusted to the 4:3 ratio when the transmissions changed.

In the 1950s, movie studios moved towards widescreen aspect ratios such as CinemaScope in an effort to distance their product from television. Although this was initially just a gimmick, widescreen is still the format of choice today and square aspect ratio movies are rare. Some people argue that widescreen is actually a disadvantage when showing objects that are tall instead of panoramic, others say that natural vision is more panoramic than tall, and therefore widescreen is easier on the eye.

The switch to digital television systems has been used as an opportunity to change the standard television picture format from the old ratio of 4:3 (1.33:1) to an aspect ratio of 16:9 (approximately 1.78:1). This enables TV to get closer to the aspect ratio of modern widescreen movies, which range from 1.66:1 through 1.85:1 to 2.35:1. There are two methods for transporting widescreen content, the most common of which uses what is called anamorphic widescreen format.

This format is very similar to the technique used to fit a widescreen movie frame inside a 1.33:1 35mm film frame. The image is compressed horizontally when recorded, then expanded again when played back. The anamorphic widescreen 16:9 format was first introduced via European PALPlus television broadcasts and then later on "widescreen" DVDs; the ATSC HDTV system uses straight widescreen format, no horizontal compression or expansion is used.

Recently "widescreen" has spread from television to computing where both desktop and laptop computers are commonly equipped with widescreen displays. There are some complaints about distortions of movie picture ratio due to some DVD playback software not taking account of aspect ratios; but this may subside as the DVD playback software matures.

Furthermore, computer and laptop widescreen displays are in the 16:10 aspect ratio both physically in size and in pixel counts, and not in 16:9 of consumer televisions, leading to further complexity. This was a result of widescreen computer display engineers' uninformed assumption that people viewing 16:9 content on their computer would prefer that an area of the screen be reserved for playback controls, subtitles or their Taskbar, as opposed to viewing content full-screen.

Transmission Band

There are various bands on which televisions operate depending upon the country. The VHF and UHF signals in bands III to V are generally used. Lower frequencies do not have enough bandwidth available for television. Although the BBC initially used Band I VHF at 45 MHz, this frequency is no longer in use for this purpose. Band II is used for FM radio transmissions. Higher frequencies behave more like light and do not penetrate buildings or travel around obstructions well enough to be used in a conventional broadcast TV system, so they are generally only used for satellite broadcasting, which uses frequencies around 10 GHz. TV systems in most countries relay the video as an AM (amplitude-modulation) signal and the sound as a FM (frequency-modulation) signal. An exception is France, where the sound is AM.

Terminology for Televisions

Pixel resolution is the amount of individual points known as pixels on a given screen. A typical resolution of 720x480 means that the television display has 720 pixels across and 480 pixels on the vertical axis. The higher the resolution on a specified display the sharper the image. Contrast ratio is a measurement of the range between the brightest and darkest points on the screen. The higher the contrast ratio, the better looking picture there is in terms of richness, deepness, and shadow detail.

The brightness of a picture measures how vibrant and impacting the colors are. Measured in cd / m2 equivalent to the amount of candles required to power the image.

On the other hand, the so-called brightness and contrast adjustment controls on televisions and monitors are traditionally used to control different aspects of the picture display. The brightness control shifts the black point, or shadow level, primarily affecting the contrast ratio or gamma of the image, while the contrast control primarily controls the image intensity or brightness.

Color Television

Color television systems were invented and patented even before black-and-white television was working; see History of television for details.

Completely electronic television systems relied on the inventions of Philo Taylor Farnsworth, Vladimir Zworykin and others to produce a system suitable for mass distribution of television programming. Farnsworth gave the world's first public demonstration of an all-electronic television system at the Franklin Institute in Philadelphia on 25 August 1934.

Regular broadcast programming occurred in the United States, the United Kingdom, Germany, France, and the Soviet Union before World War II. The first regular television broadcasts with a modern level of definition (240 or more lines) were made in England in 1936, soon upgraded to the so-called "System A" with 405 lines. Regular network broadcasting began in the United States in 1946, and television became common in American homes by the middle 1950s.

While North American over-the-air broadcasting was originally free of direct marginal cost to the consumer (i.e., cost in excess of acquisition and upkeep of the hardware) and broadcasters were compensated primarily by receipt of advertising revenue, increasingly United States television consumers obtain their programming by subscription to cable television systems or direct-to-home satellite transmissions.

In the United Kingdom, France, and most of the rest of Europe, on the other hand, operators of television equipment must pay an annual license fee, which is usually used to fund (wholely or partly) the appropriate national public service broadcaster/s (e.g. British Broadcasting Corporation, France Télévisions, etc.).

Electromechanical Techniques

Electromechanical techniques were developed from the 1900s into the 1920s, progressing from the transmission of still photographs, to live still duotone images, to moving duotone or silhouette images, with each step increasing the sensitivity and speed of the scanning photoelectric cell. John Logie Baird gave the world's first public demonstration of a working television system that transmitted live moving images with tone graduation (grayscale) on 26 January 1926 at his laboratory in London, and built a complete experimental broadcast system around his technology.

Baird further demonstrated the world's first color television transmission on 3 July 1928. Other prominent developers of mechanical television included Charles Francis Jenkins, who demonstrated a primitive television system in 1923, Frank Conrad who demonstrated a movie-film-to-television converter at Westinghouse in 1928, and Frank Gray and Herbert E. Ives at Bell Labs who demonstrated wired long-distance television in 1927 and two-way television in 1930.

Television History

Television was not invented by a single person, but by the contributions of several individuals. The origins of what would become today's television system can be traced back to the discovery of the photoconductivity of the element selenium by Willoughby Smith in 1873 followed by the work on the telectroscope and the invention of the scanning disk by Paul Nipkow in 1884. All practical television systems use the fundamental idea of scanning an image to produce a time series signal representation. That representation is then transmitted to a device to reverse the scanning process. The final device, the television (or TV set), relies on the human eye to integrate the result into a coherent image.

Television

Television is a telecommunication system for broadcasting and receiving moving pictures and sound over a distance. The term has come to refer to all the aspects of television from the television set to the programming and transmission. The word is derived from mixed Latin and Greek roots, meaning "far sight": Greek "tele", far, and Latin visio-n, sight (from video, vis- to see).